ARTEK / GLOSSARY

Ferrite core and EMI filter glossary

Short definitions of 42 terms you meet in datasheets and enquiries. Each definition names the manufacturer source it rests on and, where there is one, the guide that covers the topic in detail.

A

Air gap
An air gap is a section of a core's magnetic path where the ferrite is interrupted, so that the magnetic circuit consists of high-permeability ferrite together with a region whose permeability is that of air. It lowers the effective permeability of the core and reduces the loss factor and temperature coefficient in the same ratio. Data sheets therefore give the effective permeability separately for each gapped version of a core.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What information is needed for a custom inductor or choke quote? →
AL value
The AL value is the inductance factor of a core: the inductance obtained per turn squared, so that the inductance of a winding equals the AL value multiplied by the square of the number of turns. It is given in the data sheet for each core and material, usually in nanohenries with a tolerance, and lets a designer work out the number of turns needed for a target inductance.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: How to choose a ferrite toroid core: sizes, material, AL value and coating →

B

Bobbin (coil former)
A bobbin, or coil former, is the part on which the winding is wound and to which the core halves are then fitted; it has flanges, a tube that the core passes through and often pins for soldering to a circuit board. Its data sheet gives the winding cross-section and the average turn length, which determine how many turns of a given wire will fit and what the winding's DC resistance will be.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What information is needed for a custom transformer quote? →

C

Cable ferrite (clip-on ferrite)
A cable ferrite is a ferrite core fitted around a cable, where it acts as a one-turn common-mode choke that adds high-frequency resistance to the cable. It reduces the common-mode current and with it the emission from, or pick-up by, the cable, with little or no impedance at low frequencies or DC. Several turns through the core raise the impedance but degrade high-frequency performance; snap-on split cores can be fitted to existing cables.Source: Fair-Rite: Ferrite Cores for Low-Frequency EMI Cable SuppressionGuide: How to choose a cable ferrite: diameter, frequency and installation →
Common mode
Common mode describes interference whose current flows in the same direction along all the connecting lines and returns to its source through ground. It arises from parasitic capacitances and ground connections and becomes the dominant form of conducted interference at higher frequencies. It is reduced with current-compensated chokes and Y capacitors, which are selected separately from the differential-mode components.Source: TDK: EMC filters, Technical informationGuide: How to choose a single-phase EMI filter: current, leakage and installation →
Common-mode choke
A common-mode choke is a current-compensated choke with two windings of equal turns on a closed core, connected so that the magnetic flux from the operating current in one winding is cancelled by the other. The useful current therefore does not saturate the core, while common-mode interference meets a high inductance. High-permeability MnZn ferrite is widely used for the core, and NiZn ferrite is chosen for suppression at very high frequencies.Source: TDK: Ferrites and accessories, Application notesGuide: How to choose a single-phase EMI filter: current, leakage and installation →
Core loss
Core loss is the power dissipated in a magnetic core when it is driven by an alternating field, made up of hysteresis, eddy-current and residual losses. It depends on temperature, frequency and flux density as well as on the ferrite material and the core shape. Data sheets for power cores state it at a specific frequency, flux density and temperature, and winding losses must be added to find the total loss of a component.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →
Curie temperature
The Curie temperature is the temperature above which a ferrite loses its ferrimagnetic properties and its initial permeability falls to that of air. The effect is reversible: the magnetic properties return when the material cools below this temperature. The saturation flux density also falls steadily to zero as this temperature is approached, so the Curie temperature sets an upper limit on the working temperature of a core.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →

D

DC resistance (DCR)
DC resistance (DCR) is the resistance of an inductor's winding measured with no alternating current, expressed in ohms and usually specified as a maximum value. It determines the copper loss, which is the square of the current multiplied by the resistance and is turned into heat. A lower DCR therefore allows a higher rated current for the same temperature rise.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom inductor or choke quote? →
Differential mode
Differential mode describes interference whose current flows to the disturbed equipment on one line and back to the source on the other, just as the normal line current does. It is the main form of conducted interference at lower frequencies. It is reduced with X capacitors connected between the lines and with series inductors, so a filter contains these parts in addition to its common-mode components.Source: TDK: EMC filters, Technical informationGuide: How to choose a single-phase EMI filter: current, leakage and installation →
Drum core
A drum core is a magnetic core shaped like a bobbin or spool, with a flange at each end between which the wire is wound directly. It is available with or without leads, in axial and radial forms. An unshielded drum core has an open magnetic path, so a magnetic sleeve or a similar measure is used when a shielded inductor is required.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: How to choose a ferrite drum core: drum core vs plastic bobbin, and a selection checklist →

E

E core (EE)
An E core (EE) is a ferrite core shaped like the letter E, normally used as a pair of two halves around a bobbin that carries the winding. It allows simple bobbin winding and easy assembly but does not shield itself magnetically. E cores are offered in different thicknesses, which gives a choice of cross-sectional areas, and are used in power, converter and broadband transformers and in inductors.Source: Magnetics: Learn More about Ferrite ShapesGuide: How to choose an EE ferrite core: EE25 and EE42 replacement checks →
Eddy current
An eddy current is a current induced in a conductive material by an alternating magnetic flux, flowing in a plane perpendicular to the flux lines. Eddy currents cause losses both in the magnetic core, if the core material conducts electricity, and in the winding, where they appear as skin and proximity effects. Core materials with high electrical resistivity keep these losses low as frequency rises.Source: Vishay: Inductor and Magnetic Product Terminology
Effective magnetic cross-section (Ae)
The effective magnetic cross-section (Ae) is the cross-sectional area of an imaginary ring core that has the same magnetic properties as the real core, calculated from the core geometry. It is given in each core data sheet in square millimetres and, together with the effective path length, sets the AL value. The flux density in the core is found from it, while the minimum cross-section is used to find the maximum flux density.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: How to choose an EE ferrite core: EE25 and EE42 replacement checks →
Effective magnetic path length (le)
The effective magnetic path length (le) is the length of the magnetic path of an imaginary ring core that has the same magnetic properties as the real core, calculated from the core geometry. It is given in each core data sheet in millimetres. Divided by the effective cross-section it gives the form factor of the core, which links permeability to inductance, and it is needed to work out the effect of an air gap.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: How to choose an EE ferrite core: EE25 and EE42 replacement checks →
Effective permeability
Effective permeability is the permeability of a complete core that contains an air gap, treating the gapped magnetic circuit as if it were a closed core made of one uniform material. It is lower than the initial permeability of the ferrite and falls as the gap widens. Data sheets list it for each gapped core because the inductance, loss factor and temperature coefficient of the finished part scale with it.Source: TDK: Ferrites and accessories, General – Definitions
EMC
EMC (electromagnetic compatibility) is the ability of equipment to work properly in its electromagnetic environment without causing unacceptable disturbance to other equipment there. It covers both the emissions of a device and its susceptibility to interference from others. Standards set limit values for both, and components such as EMC filters and chokes are used to keep conducted interference within those limits.Source: TDK: EMC filters, Technical informationGuide: How to choose a single-phase EMI filter: current, leakage and installation →
EMI
EMI (electromagnetic interference) is unwanted electrical energy in any form, and the term is often used interchangeably with noise. It is most often generated by switching circuits such as switching voltage regulators and clocked digital circuits. Filters built from inductors and capacitors attenuate it, and the frequency range of the interference is the starting point for choosing suppression parts.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: How to choose a cable ferrite: diameter, frequency and installation →
EMI filter
An EMI filter is an electrical circuit of inductors, capacitors and resistors that limits electrical interference on power lines. It is almost always a low-pass filter: the mains or DC supply frequency passes largely unaffected, while interference frequencies are weakened. Its main parts are X and Y capacitors, differential-mode chokes and current-compensated chokes, and it is built with two, three or four lines depending on the type of supply.Source: TDK: EMC filters, Technical informationGuide: How to choose a single-phase EMI filter: current, leakage and installation →
ETD core
An ETD core is an E-type ferrite core with a round centre post, with dimensions optimised for power transformer efficiency. The round centre post keeps the winding resistance to a minimum, because each turn is shorter than on a square post of the same area. ETD cores come in a series of industry-standard sizes and are typically used in power transformers and differential inductors.Source: Magnetics: Learn More about Ferrite ShapesGuide: ETD29, ETD39 or ETD44: how to choose a ferrite core for an SMPS →

F

Ferrite bead
A ferrite bead is a noise-suppression inductor formed by passing a conductor through a piece of ferrite, or by building a coil inside a ferrite chip, using ferrite that has high loss at high frequencies. Connected in series, it acts as a low-pass filter whose high-frequency impedance is mainly resistive, so noise energy is absorbed as loss in the ferrite. Beads are selected by their impedance curve in relation to the signal and noise frequencies.Source: Murata: Basics of Noise Countermeasures, Lesson 4: Chip ferrite beads
Flyback transformer
A flyback transformer is the magnetically coupled inductor of a flyback converter: energy is stored in it while current flows in the primary winding and is passed to the output through the secondary winding when the switch turns off. It provides galvanic isolation, and the output voltage is set by the turns ratio, with extra secondary windings giving extra outputs. Because it stores energy, its core needs an air gap, unlike an ordinary transformer.Source: Ferroxcube: Soft Ferrites and Accessories data handbookGuide: What information is needed for a custom transformer quote? →

H

Hysteresis
Hysteresis is the behaviour of a magnetic material in which the flux density follows a different curve when the magnetic field is reduced than when it was increased, so that plotting one against the other gives a closed loop. Some flux density remains when the field returns to zero. Core loss is proportional to the area of the loop, so the shape of the loop indicates how much power a material will dissipate.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What is a ferrite core and what does it do? Soft ferrite, MnZn and NiZn explained →

I

Impedance
Impedance is the total opposition of a component to the flow of current, combining its DC resistance with a frequency-dependent AC part, and is measured in ohms. For an ideal inductor the AC part is the inductive reactance, which rises with both inductance and frequency; skin effect and core losses add to it. Impedance is therefore always quoted at a stated frequency.Source: Vishay: Inductor and Magnetic Product Terminology
Inductance
Inductance is the property of a circuit element that opposes any change in the current flowing through it, measured in henries. For a given inductor it is set by the core material, the shape and size of the core, the number of turns and the shape of the coil. The value is stated with a tolerance and is measured at a defined test frequency.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom inductor or choke quote? →
Initial permeability
Initial permeability is the relative permeability of a magnetic material at very low excitation levels, measured on a closed magnetic circuit such as a ring core. It is the main figure used to compare soft magnetic materials, so it is usually the first value to check when choosing a ferrite material. It changes with temperature and with mechanical stress on the core.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →
Iron-powder core
An iron-powder core is a magnetic core pressed from iron particles that are insulated from each other and held by a binder, which gives the material a distributed air gap. This lets the core carry a higher DC current before it saturates than a ferrite core, and its saturation is gradual. Its permeability is also more stable with temperature than that of ferrite.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: Ferrite vs iron-powder toroids: which core suits your inductor? →

L

Leakage current (of a mains filter)
Leakage current is the current that flows to ground or to an external conductive part in a fault-free circuit; in a mains filter it flows through the casing to the reference potential at the rated frequency. It is caused mainly by the capacitors connected to ground, the Y capacitors. The leakage currents of all parts of an installation add up, so the filter's value is checked against the limit for the whole equipment.Source: TDK: EMC filters, Technical informationGuide: How to choose a single-phase EMI filter: current, leakage and installation →
Leakage inductance
Leakage inductance is the inductance that remains in a transformer because the coupling between the primary and secondary windings is less than perfect; it behaves like an inductance in series with the primary. In a flyback transformer it produces a high voltage and ringing across the switch at turn-off, which a snubber network has to absorb. It is reduced, but never eliminated, by filling each winding layer and by interleaving the windings.Source: Bourns: Designing a Low Power Flyback Power Supply (application note)Guide: What information is needed for a custom transformer quote? →
Litz wire
Litz wire is a conductor made of many separately insulated strands that are woven or bunched together so that each strand takes every possible position in the cross-section of the wire. The current is shared equally between the strands, which gives lower AC losses than a comparable solid wire. The benefit grows as the operating frequency increases, where skin effect would otherwise raise the winding resistance.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom transformer quote? →

M

MnZn ferrite
MnZn ferrite is a soft ferrite based on manganese and zinc that offers higher permeability and higher saturation flux density than NiZn ferrite. Its resistivity is lower, so it suits the lower part of the frequency range in which ferrites are used. It is the usual choice for power-conversion cores and for the common-mode chokes in mains input filters.Source: Ferroxcube: Soft Ferrites and Accessories data handbookGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →

N

NiZn ferrite
NiZn ferrite is a soft ferrite based on nickel and zinc that has a very high electrical resistivity. This makes it the more suitable ferrite family at higher frequencies, while its permeability and saturation flux density are lower than those of MnZn ferrite. It is commonly chosen for interference suppression at high frequencies and for radio-frequency inductors and transformers.Source: Ferroxcube: Soft Ferrites and Accessories data handbookGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →

R

Rated current
Rated current is the continuous DC current an inductor can carry without exceeding a stated temperature rise at its maximum rated ambient temperature. It depends on the DC resistance of the winding and on how well the part sheds heat, not on the magnetic properties of the core. A part should be checked against both its rated current and its saturation current, because either limit can be reached first.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom inductor or choke quote? →
Rod core
A rod core is a magnetic core in the shape of a cylindrical rod, with or without leads. Its magnetic path is open, so most of the magnetic energy is stored in the air around the core rather than inside it. This lets it withstand higher flux levels than closed shapes, but a rod inductor is unshielded and its field reaches nearby parts.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: How to choose a ferrite rod core: checklist for diameter, length, material and winding →

S

Saturation
Saturation is the condition in which a magnetic core cannot store any more magnetic flux, so its permeability falls as the current through the winding rises further. The inductance of the part then drops, sharply in ferrite cores and more gradually in iron-powder cores. A core is therefore chosen so that the highest current in the circuit stays below the point where saturation begins; air-core inductors do not saturate.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom inductor or choke quote? →
Saturation current
Saturation current is the DC bias current through an inductor at which its inductance has fallen by a specified percentage from the value measured with no DC current. The percentage differs between manufacturers and core materials, so two parts can only be compared when the stated inductance drop is the same. It is a magnetic limit set by the core and is separate from the rated current, which is a thermal limit.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: What information is needed for a custom inductor or choke quote? →
Saturation flux density
Saturation flux density is the highest magnetic flux density a material can reach at a given temperature; beyond it, a stronger magnetic field no longer increases the flux density. It falls as temperature rises and reaches zero at the Curie temperature. The value at the actual operating temperature, not the room-temperature value, therefore sets how far a core can be driven.Source: TDK: Ferrites and accessories, General – DefinitionsGuide: What do CF139, CF297 and CF199 mean? How to read ferrite core material codes and check an N87 equivalent →
Skin effect
Skin effect is the tendency of alternating current to flow near the surface of a conductor instead of using its whole cross-section. It raises the resistance of the conductor, and the current is pushed further towards the surface as frequency increases. It therefore adds to winding losses at high frequency, and is the reason stranded conductors such as litz wire are used.Source: Vishay: Inductor and Magnetic Product Terminology
SMPS (switched-mode power supply)
An SMPS (switched-mode power supply) is a power supply that efficiently converts electrical power into the voltage and current levels a load requires by switching a transistor on and off and using an inductor or transformer to store and transfer the energy. Common converter types are buck, boost, flyback, forward and bridge converters. The converter type and operating frequency decide which core material and shape are suitable.Source: Ferroxcube: Soft Ferrites and Accessories data handbookGuide: What information is needed for a custom transformer quote? →
Soft ferrite
Soft ferrite is a brittle, chemically inert ceramic magnetic material that is easily magnetised, with the general composition MeFe2O4 where Me stands for one or more metals such as manganese, zinc or nickel. Its high intrinsic resistivity allows it to be used up to very high frequencies without the laminations that magnetic metals need. The two most common families are manganese-zinc and nickel-zinc ferrite.Source: Ferroxcube: Soft Ferrites and Accessories data handbookGuide: What is a ferrite core and what does it do? Soft ferrite, MnZn and NiZn explained →

T

Toroid core
A toroid core is a ring-shaped magnetic core on which the winding is placed directly, forming a closed magnetic path. Because the flux stays largely inside the ring, a toroidal inductor is self-shielding and gives high coupling between windings. Toroids are available in ferrite, iron powder and other magnetic materials, so the material must be stated along with the dimensions.Source: Vishay: Inductor and Magnetic Product TerminologyGuide: How to choose a ferrite toroid core: sizes, material, AL value and coating →

U

U core (UU, UI)
A U core is a ferrite core shaped like the letter U, used either as two U halves (UU) or as a U closed with a straight I bar (UI). Its long legs support designs with low leakage inductance and make good voltage isolation between windings easier. U cores suit power transformers that work at higher power in tight spaces or unusual form factors.Source: Magnetics: Learn More about Ferrite ShapesGuide: How to choose a UU ferrite core: checklist for line filters and power transformers →

If the term you need is not here, write to us and we will add it. To read the topics in order, see the technical library.